Raypak Electric Heater Finned Water Tube Water Heaters User Guide

Catalog No.: 3500.90C  
Effective:  
Replaces:  
RAYTHERM, TYPE WH  
SUGGESTED SPECIFICATIONS  
6-1-08  
5-1-05  
DIVISION 23 52 33.13  
FINNED WATER-TUBE WATER HEATERS  
PART 1 - GENERAL  
1.1 SUMMARY  
A. Section includes gas-fired, copper finned-tube water heaters for use with a storage tank.  
B. Related Sections  
Specifier Note: Use as needed  
1. Building Services Piping – Division 23 21 00  
2. Breeching, Chimneys, and Stacks (Venting) – Division 23 51 00  
3. HVAC Instrumentation and Controls – Division 23 09 00  
4. Electrical – Division 23 09 33  
1.2  
REFERENCES  
A. ANSI Z21.10.3/CSA 4.3  
B. ASME, Section IV  
C. 2006 UMC, Section 1107.6  
D. National Fuel Gas Code  
E. NEC  
1.3  
1.4  
SUBMITTALS  
A. Product data sheet (including dimensions, rated capacities, shipping weights, accessories)  
B. Wiring diagram  
C. Warranty information  
D. Installation and operating instructions  
QUALITY ASSURANCE  
A. Regulatory Requirements  
1. ANSI Z21.10.3/CSA 4.3  
B. Certifications  
1. CSA  
2. ASME HLW Stamp and National Board Listed  
3. ISO 9001  
1.5  
HEAT EXCHANGER WARRANTY  
A. Limited five-year warranty from date of installation  
B. Limited twenty-year thermal shock warranty from date of installation  
C. Limited ten-year warranty for cupro-nickel heat exchangers only  
PART 2 - PRODUCTS  
2.1  
MANUFACTURER  
A. Raypak, Inc.  
1. Contact: 2151 Eastman Ave., Oxnard, CA 93030; Telephone: (805) 278-5300;  
2. Product: Raytherm® copper finned-tube water heater(s)  
2.2  
WATER HEATERS  
A. General  
Project Name / Date  
Division 23 52 33.13 - 1  
 
1. The water heater(s) shall be equipped to (a), (b), or (c):  
a. Provide full modulation of gas input to any load condition as low as 20% of the full rating of  
the water heater (5:1 ratio) without flashback, burning at orifices or improper combustion.  
b. Provide staged control of the gas input to the water heater.  
c. Provide on/off control of the gas input to the water heater.  
H. Water Heater Diagnostics  
1. Provide ignition module indicating the following heartbeats (flashes) by LED signal:  
“M” Ignition Model (Continuous Retry)  
a. 2 flashes per second (“heartbeat”) – Normal operation  
b. 2 flashes – Five-minute retry delay  
c. 3 flashes – Recycle; flame failed during run  
d. 4 flashes – Flame sensed out of sequence  
e. 7 flashes – Flame sense leakage to ground  
f. 8 flashes – Low 24VAC (secondary voltage)  
g. 6+2 flashes – Five-minute retry delay (on every third retry on the same “Call For Heat”  
h. 6+3 flashes – On every sixth flame failure during run on the same “Call For Heat”  
i. 6+4 flashes – Flame sensed out of sequence for more than 10 seconds  
j. ON steady – Soft lockout due to error detected during self-check sequences  
“H” Ignition Model (Lockout)  
k. 2 flashes per second (“heartbeat”) – Normal operation  
l. 2 flashes – Five-minute retry delay  
m. 3 flashes – Recycle; flame failed during run  
n. 4 flashes – Flame sensed out of sequence  
o. 7 flashes – Flame sense leakage to ground  
p. 8 flashes – Low 24VAC (secondary voltage)  
q. 6+2 flashes – Failed trial for ignition resulting in lockout  
r. 6+3 flashes – More than five flame failures during run on the same “Call For Heat” resulting  
in lockout  
s. 6+4 flashes – Flame sensed out of sequence for more than 10 seconds  
t. ON steady – Soft lockout due to error detected during self check sequences  
I. Combustion Chamber: The high-temperature, multi-piece, interlocking castable combustion  
chamber liner shall reduce standby radiation losses, reducing jacket losses and increasing unit  
efficiency.  
J. Venting  
1. When routed vertically, the water heater’s flue material and size shall be in accordance with  
the National Fuel Gas Code, ANSI Z223.1/NFPA54 latest edition (Category I).  
K. Cabinet  
1. The corrosion-resistant galvanized steel jackets shall be finished with a baked-on epoxy  
powder coat which is suitable for outdoor installation, applied prior to assembly for complete  
coverage, and shall incorporate louvers in the outer panels to divert air past heated surfaces.  
2. The water heater(s), if located on a combustible floor, shall require an optional separate  
combustible floor base.  
L. Operating Controls  
1. The water heater(s) shall feature an optional temperature controller.  
Specifier Note: The remaining items in this section are options. Delete those that are not being  
specified. IMPORTANT: The Cold Water Start and Cold Water Run Systems cannot be  
used on the same water heater.  
M. Water Heater Pump - Refer to Equipment Schedule  
N. Cold Water Start System  
1. The water heater(s) shall be configured with a cold water start automatic proportional bypass  
system that ensures the water heater will experience inlet temperatures in excess of 105ºF  
within 7 minutes to avoid damaging condensation. The unit will automatically shut down if the  
Project Name / Date  
Division 23 52 33.13 - 3  
 
inlet temperature is not achieved within the 7-minute time frame.  
2. The cold water start system shall be configured with a modulating three-way valve that is  
controlled by a system-matched PID controller. The PID controller temperature sensor shall be  
located in the inlet header of the water heater.  
3. The control shall have a temperature setting dial located on the face of the board. The  
temperature range of the dial shall be 105ºF to 120ºF. The PID Logic shall be capable of  
limiting system overshoot to a maximum of 10ºF on initial start-up or call-for-heat.  
4. The cold water start system shall be completely wired and mounted at the factory.  
5. The control shall have the following diagnostic LED’s:  
a. Call for heat  
b. Start-up mode  
c. Inlet temperature error  
d. Sensor out of range  
6. The controller shall have the capability to add optional alarm contacts.  
O. Cold Water Run System  
1. The water heater(s) shall be configured with a cold water run automatic proportional bypass  
system that ensures the water heater will experience inlet temperatures in excess of 105ºF  
within 7 minutes to avoid damaging condensation. The unit will automatically shut down if the  
inlet temperature is not achieved within the 7-minute time frame.  
2. The cold water run system shall be configured with a variable speed pump that is controlled by  
a system-matched PID control that injects the correct amount of cold water directly into the  
water heater loop to maintain a minimum inlet temperature. The PID controller temperature  
sensor shall be located in the inlet header of the water heater.  
3. The control shall have a temperature setting dial located on the face of the board. The  
temperature range of the dial shall be 105ºF to 120ºF. The PID Logic shall be capable of  
limiting system overshoot to a maximum of 10ºF on initial start-up or call-for-heat.  
4. The cold water run system shall be completely wired and mounted at the factory.  
5. The control shall have the following diagnostic LED’s:  
a. Call for heat  
b. Start-up mode  
c. Inlet temperature error  
d. Sensor out of range  
6. The controller shall have the capability to add optional alarm contacts.  
2.3  
SOURCE QUALITY CONTROL  
A. The water heater(s) shall be completely assembled, wired, and fire-tested prior to shipment from  
the factory.  
B. The water heater(s) shall be furnished with the sales order, ASME Manufacturer’s Data Report,  
inspection sheet, wiring diagram, rating plate and Installation and Operating Manual.  
PART 3 - EXECUTION  
3.1  
INSTALLATION  
A. Must comply with:  
1. Local, state, provincial, and national codes, laws, regulations and ordinances  
2. National Fuel Gas Code, NFPA 54/ANSI Z223.1 – latest edition  
3. National Electrical Code, ANSI/NFPA 70 – latest edition  
4. Canada only: CAN/CSA B149 Installation Code and CSA C22.1 CEC Part I  
5. Manufacturer’s installation instructions, including required service clearances and venting  
guidelines  
B. Manufacturer’s representative to verify proper and complete installation.  
3.2  
START-UP  
A. Shall be performed by Raypak factory-trained personnel.  
B. Test during operation and adjust if necessary:  
Project Name / Date  
Division 23 52 33.13 - 4  
 
1. Safeties (2.2 - F)  
2. Operating Controls (2.3)  
3. Static and full load gas supply pressure  
4. Gas manifold and blower air pressure  
C. Submit copy of start-up report to Architect and Engineer.  
TRAINING  
3.3  
A. Provide factory-authorized service representative to train maintenance personnel on procedures  
and schedules related to start-up, shut-down, troubleshooting, servicing, and preventive  
maintenance.  
B. Schedule training at least seven days in advance.  
END OF SECTION  
Project Name / Date  
Division 23 52 33.13 - 5  
 

RCA CD Player RP 9328 User Guide
Roadmax GPS Receiver VMAX361 User Guide
Saitek Games Talking Chess Trainer User Guide
Sakar Digital Camera 16380 User Guide
Samsung Microwave Oven M1732N User Guide
Samsung Projector BP59 00140E 01 User Guide
Sanyo Camcorder VM ES 88 P User Guide
Sanyo Digital Camera HD2100 User Guide
Sanyo Indoor Furnishings POA CH EX06 User Guide
Sears Lawn Mower 6 3041 User Guide