Runco Projector DR 300c User Guide

OWNERS OPERATING MANUAL  
DR-300c Projector  
& PFP Controller  
Digital Light Processing™ Projector &  
Pixel For Pixel™ Controller with Vivix™ Technology  
www.htrgroup.com  
 
Table of Contents  
Introduction ........................................................................................................ 3  
Warnings and Safety Precautions .................................................................... 4  
Warning .......................................................................................................... 5  
Safety Tips ...................................................................................................... 5  
Limited Warranty ................................................................................................ 6  
Feature and Benefits .......................................................................................... 8  
Projector Description ........................................................................................ 9  
LED View ........................................................................................................ 9  
Side View ........................................................................................................ 9  
Projector Placement and Offset Information ................................................ 10  
Ceiling Mount Configuration.......................................................................... 10  
Floor Mount Configuration ............................................................................ 10  
PFP Controller Description .............................................................................. 11  
Front Panel.................................................................................................... 11  
Rear Panel .................................................................................................... 12  
Remote Control Description............................................................................ 13  
Quick Set-up Guide .......................................................................................... 14  
Connection Example .................................................................................... 14  
Overall Functional Description........................................................................ 15  
Menu Description and Navigation .................................................................. 16  
Menu Tree .................................................................................................... 16  
Main Menu .................................................................................................... 16  
Picture Quality Adjustments............................................................................ 18  
Main Menu .................................................................................................... 18  
Installation Menu................................................................................................21  
Installation Menu ............................................................................................21  
Screen Type ..................................................................................................21  
16:9 Position ..................................................................................................22  
Keystone ........................................................................................................22  
Picture Orientation..........................................................................................23  
Lamp Hours....................................................................................................23  
System Reset ................................................................................................23  
Quick Menu ...................................................................................................... 24  
Basic Troubleshooting Tips..............................................................................25  
RS-232 Communications ..................................................................................27  
RS-232 Commands........................................................................................28  
Dimensions........................................................................................................ 30  
Specifications.................................................................................................... 32  
1
 
2
 
Introduction  
The DR-300c is Runco's second generation in the award winning Reflection series of  
DLP™ projectors. With a native resolution of 1024 x 768, the DR-300c is fully DTV compati-  
ble, and will accept and display all ATSC HDTV formats including 720p and 1080i. With an  
incredible 1000 ANSI lumen light output capability, the DR-300c can deliver the big screen  
home theater experience. The projector’s sleek high-tech design gives it a small footprint,  
while its features - including electronic keystone correction - add flexibility and versatility nec-  
essary for challenging installations. This versatility combined with the DR-300’s excellent pic-  
ture quality make it the perfect solution for a maintenance free big screen home theater. The  
DR-300c's PFP™ (Pixel For Pixel™) Controller provides superb pixel for pixel video process-  
ing, full aspect ratio control (4:3, letterbox, and anamorphic) allowing it to be used with either  
a 4:3 or a wide aspect ratio screen, and also provides all picture controls for ease of setup.  
Features  
• 1000 ANSI Lumens of light output  
• Multiple aspect ratios: 4:3, letterbox, anamorphic  
• Electronic keystone correction  
Native 1024 x 768, Widescreen 1024 X 576  
• DTV capable (via outboard DTV decoder); 480p, 720p, 1080i  
• PAL compatible  
• 3:2 Pull down detection  
• Can be configured for 16:9 screens, 4:3 screens, or 16:9 screens with an anamorphic lens  
(optional).  
Included Accessories  
• Owner’s manual  
• Remote control  
• Power cables (one for Projector, one for PFP Controller)  
• The Installer friendly “Slam Dunk” cable (Includes all necessary input extensions)  
3
 
Warnings and Safety Precautions  
CAUTION:  
To turn off main power, be sure to remove the plugs from power outlets. The power outlet  
socket should be installed as near to the equipment as possible, and should be easily  
accessible.  
REMARQUE:  
Pour mettre l’appareil hors circut, s’assurer de retirer la fiche de la prise d’alimentation.  
La prise d’alimentation doit être installé aussi proche que possible de l’appareil et doit être  
facile d’ accès.  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO  
NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUT-  
LETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS  
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
AVERTISSEMENT  
POUR EVITER UN FEU OU UN RISQUE D’ELECTROCUTION NE PAS EXPOSER CET ENSEMBLE A LA  
PLUIE OU A L’HUMIDITE; DE MEME, NE PAS BRANCHER LA PRISE POLAIRE AVEC UNE RALLONGE A  
MOINS QUE LES DENTS DE LA PREMIERE NE S’Y INSERENT PLEINEMENT.  
EVITER D’OUVRIR LE COFFRET CAR IL Y A, A L’INTERIEUR, DES COMPOSANTS SOUMIS A UNE HAUTE-  
TENSION; POUR LES REPARATIONS, S’ADRESSER A UN PERSONNEL QUALIFIE.  
4
 
WARNING  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-  
able protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the installation manual, may cause harmful interfer-  
ence to radio communications. Operation of this equipment in a residential area is likely to  
cause harmful interference, in which case, the user will be required to correct the interference  
at his own expense.  
DOC compliance Notice  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing  
Equipment Regulations.  
DOC avis de conformation  
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le Matériel  
D’interférence du Canada.  
SAFETY TIPS  
Please read and follow the safety precautions listed below to ensure the equipment is  
free from damage, and to ensure that no injury will occur as a result of improper use.  
· Do not insert any object, especially metal or liquids, into the Projector or PFP Controller.  
· Do not place any objects containing water or any other liquid on top of the Projector  
or PFP Controller.  
· Do not place the units in direct sunlight, near heaters or in extremely dusty or humid  
locations.  
· Do not install this system outdoors or otherwise exposed to the elements.  
· Do not place heavy objects on top of the Projector or Controller.  
· If the power cord is damaged or frayed in any way, electrical shock and/or fire may result.  
Please do not place objects on the power cord, and keep the cord away from heat-emitting  
devices. Should the power cord become damaged in any way, please contact your Runco  
dealer for a replacement cord.  
· Do not remove the cover of the Projector or PFP Controller for any reason. If any problems  
arise with the unit, please contact a Runco dealer or Runco International for service.  
Removing the covers will void the warranty.  
5
 
Limited Warranty  
LIMITED WARRANTY  
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We  
believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup  
and care, you should enjoy many years of unparalleled video performance. Please read this con-  
sumer protection plan carefully and retain it with your other important documents.  
This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal  
Trade Commission Improvement Act.  
WHAT IS COVERED UNDER THE TERMS OF THIS WARRANTY:  
SERVICE LABOR: Runco will pay for service labor by an approved Runco service center when need-  
ed as a result of manufacturing for a period of two (2) years from the effective date of delivery to the  
end user.  
PARTS (Not including projector lamp): Runco will provide new or rebuilt replacement parts for the  
parts that fail due to defects in materials or workmanship for a period of two (2) years from the effec-  
tive date of the warranty. Such replacement parts are then subsequently warranted for the remaining  
portion (if any) of the original warranty period.  
LAMP: Six months or 1000 hours (which ever comes first).  
WHAT IS NOT COVERED UNDER THE TERMS OF THIS WARRANTY:  
This warranty only covers failure due to defects in materials and workmanship that occur during nor-  
mal use and does not cover normal maintenance. This warranty does not cover cabinets or any  
appearance item; any damage to laser discs; failure resulting from accident, misuse, abuse, neglect,  
mishandling, misapplication, faulty or improper installation or setup adjustments; improper mainte-  
nance, alteration, improper use of any input signal; damage due to lightning or power line surges,  
spikes and brownouts; damage that occurs during shipping or transit; or damage that is attributed to  
acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or  
improper batteries is also excluded from coverage under this warranty.  
CAUTION: DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION  
OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. IT IS  
IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHO-  
RIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL  
ALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE YOUR RUNCO PRODUCT IS  
CAPABLE OF PROVIDING WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PER-  
SONNEL.  
RIGHTS, LIMITS AND EXCLUSIONS:  
Runco limits its obligations under any implied warranties under state laws to a period not to exceed  
the warranty period. There are no express warranties. Runco also excludes any obligation on its part  
for incidental or consequential damages related to the failure of this product to function properly.  
Some states do not allow limitations on how long an implied warranty lasts, and some states do not  
allow the exclusion or limitation of incidental or consequential damages. So the above limitations or  
exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have  
other rights that vary from state to state.  
6
 
EFFECTIVE WARRANTY DATE:  
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the  
original bill of sale as evidence of the purchase date.  
IMPORTANT: WARRANTY REGISTRATION:  
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach  
you promptly if we should discover a safety problem or product update for which you must be notified.  
TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:  
Repairs made under the terms of the Limited Warranty covering your Runco International video prod-  
uct will be performed at the location of the product, during usual working hours, providing location of  
product is within normal operating distance from a Runco Authorized Service Center. If, solely in  
Runco’s judgement, location of product to be repaired is beyond normal operating distance of the  
closest Runco Authorized Service Center, it is the owner’s responsibility to arrange for shipment of the  
product for repair. These arrangements must be made through the selling Runco dealer. If this is not  
possible, contact Runco directly for a return authorization number and shipping instructions. Runco  
will return product transportation prepaid in the United States, unless no product defect is discovered.  
In that instance, shipping costs will be the responsibility of the owner.  
ADDITIONAL INFORMATION:  
To locate the name and address of the nearest Runco Authorized Service location, or for additional  
information about this warranty, please call, write or visit our website:  
CUSTOMER SERVICE DEPARTMENT  
RUNCO INTERNATIONAL  
2463 Tripaldi Way  
Hayward, CA 94545  
Ph: (510) 293-9154 / Fax: (510) 293-0201  
7
 
Features and Benefits  
The DR-300c system is a very unique system and has many important features, including:  
• Full control of the Projector via the PFP Controller. This control includes all image quality  
adjustments as well as Projector adjustments such as image configuration.  
• 1000 ANSI lumens light output.  
• Reliable lamp with 1000 hour life span.  
Native 1024 x 768, Widescreen 1024 X 576  
• RGB/Component (via 15 pin connector) port for DTV or computer signals. RGB and  
Component signals are automatically detected by the Projector for ease of operation.  
• An adaptive two-dimensional comb filter that greatly reduces artifacts when using  
Composite video.  
• A Luma edge enhancement circuit makes the edges of objects appear sharper without the  
ringing and noise associated with traditional sharpness circuits.  
• A Chroma edge enhancement circuit is included to compensate for lower chroma resolution  
found in composite and S-Video.  
• Inverse telecine (3:2 pulldown) detection and processing allows the scaler to almost  
completely eliminate interlace artifacts associated with other scalers.  
• System can be configured for 4:3 screens, 16:9 screens or 16:9 screens with an anamor-  
phic lens installed.  
• Aspect ratio control for either 16:9 or 4:3 screens provides anamorphic, 4:3 and letterbox  
ratios.  
• A Time Base corrector circuit is provided for unstable sources such as VCRs.  
• 12v outputs for drop screens and screen masking.  
• Automatic switching between NTSC and PAL signals.  
• Fully RS-232 controllable, with direct access to sources and aspect ratios.  
• A simple remote controls all aspects of operation, and includes discreet on/off, aspect ratio  
and source selection commands.  
8
 
Projector Description  
Top View  
Lens  
Lens adjustments  
• Outer ring focuses the lens  
• Inner ring zooms the image  
Status LED: indicates status of  
Projector, including any faults.  
See page 26 for fault indications.  
Status  
Power  
IR Receiver: Receives infrared  
commands from the Projector’s  
remote (not used in the DR-300c  
system).  
Power Indication:  
Green = Operation  
Blinking = Warming up/cooling  
down  
Orange = Standby  
Input Panel  
S-Video  
Video  
RGB / Component / HD  
Power Inlet  
ComLink  
Input Panel  
Bottom view of Projector  
Lamp access door  
(small flathead screwdriver required for removal of lamp)  
9
 
Projector Placement and Offset Information  
Ceiling Mount Configuration  
6.090  
2.842  
1.895  
B
Projector Base  
1.745  
Base plate to center of lens  
3.398  
C
angle  
A
Screen Top  
Half Screen  
Length  
Screen Center  
Full Screen Length  
Screen __________ (H) x __________ (W)  
NOTE: These figures  
are the same for both  
ceiling and floor  
B) THROW DISTANCE FOR 4 x 3 or 16 x 9 SCREENS:  
Minimum: = (screen width x 2.0) = __________ inches  
configurations. The  
Maximum: = (screen width x 2.3) = __________ inches  
offset figures are with  
the “16:9 Position”  
setting in the CENTER  
position (see page 22).  
C) VERTICAL OFFSET:  
Distance between lens center and top edge of viewing area (bottom edge for floor mount):  
For use on 4 x 3 ratio screens: (screen width x .173) = __________ inches  
For use on 16 x 9 ratio screens: (screen width x .265) = __________ inches  
Full Screen Length  
Screen Top  
Screen Center  
Floor Mount Configuration  
Half Screen  
Length  
A
C
angle  
3.398  
4.028  
1.745  
Base plate to center of lens  
Projector Base  
B
10  
 
PFP Controller Description  
Front Panel  
1
2
3
ratio  
p
<
>
ratio  
TM  
P
I
X
E
L
F
O
R
P
I
X
E
L
4
5
6
7
8
9
10  
1. IR RECEIVER  
Receives the infrared signal from the remote control.  
2. POWER BUTTON  
Turns the unit ON or OFF. The Main Power switch on the rear of the unit must be on first for this button to be active.  
3. POWER INDICATOR  
When the PFP Controller is ON, this LED will illuminate GREEN. When the unit is OFF or in STANDBY, this LED will  
illuminate RED. A flashing red light indicates a fault. If this happens, unplug the unit for 2 minutes and re-try. A yellow  
LED indicates a communication problem; double check that the ComLink cable is connected properly (page 10).  
4. LED DISPLAY  
Indicates the model number, current source, resolution and aspect ratio.  
5. UP BUTTON  
When no menu is present on-screen, this button will toggle you through the different aspect ratios.  
When the menu is on-screen, the UP button will move the cursor up within a menu.  
When an adjustment item has been selected (i.e. brightness), the UP button will increase the value of that function.  
6. LEFT BUTTON  
When no menu is present on-screen, the LEFT button will toggle you through the four different sources, in the order of:  
RGB/Component  
Component  
S-Video  
Composite  
7. ENTER BUTTON  
When an item is highlighted on the On-Screen Display, the ENTER button will select the item. When in the  
RGB/Component source and the installation mode is active, the ENTER button will enable the ‘Quick Menu’ on the front  
panel, which allows you to shift or blank the HD or computer image (see pg. 24).  
8. DOWN BUTTON  
When no menu is present on-screen, this button will toggle you through the different aspect ratios.  
When the menu is on-screen, the DOWN button will move the cursor down within a menu.  
When an adjustment item has been selected (i.e. brightness), the DOWN button will decrease the value of that function.  
9. RIGHT BUTTON  
When no menus are present on-screen, the RIGHT button will toggle you through the four different sources, in the order of:  
Composite  
S-Video  
Component  
RGB/Component  
10. MENU BUTTON  
The MENU button brings up the main adjustment menu. After making adjustments, the MENU button will bring you back to  
the sub-menu, then to the main menu. The menu will then either time-out after approximately 10 seconds, or pressing the  
MENU button will remove the menu immediately.  
11  
 
Rear Panel  
5
CAUTION  
RUNCO INTERNATIONAL  
HAYWARD, CA  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
!
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR  
MADE IN USA  
COMLINK OUT  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER. NO USER-  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE CENTER.  
12V FUSE  
AC 120V 60Hz, 15W  
WARNING: TO REDUCE THE RISK OF FIRE  
OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE.  
RGB OUTPUT  
B
VIDEO INPUTS  
RS-232 IN  
V
H
G
R
RGB/COMPONENT  
Y
Pr  
Pb  
S-VIDEO COMPOSITE  
MASK  
SCREEN  
MADE IN USA  
12V TRIGGER  
1
2
3
4
6
7
8
9
10  
11 12  
13  
1. 12v FUSE  
This fuse protects the 12v outputs from the MASK and SCREEN jacks.  
(Screen Fuse: 5mm x 25mm, AGC, 0.5A, 250V, Fast Blow)  
2. MASK  
This is a 12V output that can be used to trigger curtains, lifts, etc. (1/4A maximum load).  
3. SCREEN  
This is a 12V output that can be used to trigger curtains, lifts, etc. (1/4A maximum load).  
4. RS-232 IN  
This is for systems using serial (RS-232) to control the PFP Controller.  
Please refer to page 27 for RS-232 protocol and information.  
5. COMLINK OUT  
The output of this jack must be connected to the ComLink input of the DR-300c. If this is not connected, neither  
the PFP Controller or the Projector can operate and the power indicator on the front panel will stay yellow.  
6. RGB OUTPUT  
This is the main output of the PFP Controller. The RGB Signal goes directly to the Projector. If  
Component is used through the RGB/Component, then only the R (Pr), G(Y) and B(Pb) jacks will be active.  
Individually, the jacks are: V=vertical sync, H=horizontal sync, B=Blue, G=Green, R=Red.  
7. RGB/COMPONENT  
Anything input to this port will by-pass the processing of the PFP Controller and be sent straight to the dis-  
play. This is useful for computer graphics and HDTV signals which do not require processing.  
8. COMPONENT INPUT  
This is the input for Component Video from sources such as DVD players.  
Note: The component output from a DTV decoder or a progressive-scan DVD cannot be used with this port;  
it must be used with the RGB/Component port.  
9. S-VIDEO INPUT  
This is the input for S-Video from sources such as Satellite receivers, S-VHS VCR’s and DVD players.  
10. COMPOSITE VIDEO INPUT  
This is the input for Composite Video from sources such as laser disc players, VCRs and other misc. sources.  
11. POWER INPUT  
Plug in Main Power here.  
12. 115 VAC FUSE  
13. MAIN POWER SWITCH  
This is the main AC Input fuse (.5A/250V).  
Disconnects or applies main power to the Controller.  
12  
 
Remote Control Description  
A. IR OUTPUT INDICATOR  
Illuminates when a button is pressed, indicating that an IR signal is being  
A
B
transmitted.  
B. POWER BUTTON  
Toggles the power on and off. For a discrete on or off command, you can  
use the direct access buttons (see 'J'). Note: When the main AC power  
switch is first turned ON, the PFP Controller will go through an initiation  
cycle for approximately 15 seconds. The PFP Controller cannot be turned  
on or operated until the initialization is complete.  
PWR  
C
D
G
F
P
P
M
C. UP BUTTON  
When no menus are present on-screen, the UP button will toggle you  
through aspect ratios in the following order:  
I
H
Letterbox  
Standard (4:3)  
Anamorphic  
E
When the menu is on-screen, the UP button will move the cursor up within  
the menu. When an adjustment item has been selected (i.e. brightness),  
the UP button will increase the value of that function.  
1
4
7
2
5
8
0
3
J
6
D. LEFT BUTTON  
When no menus are present on-screen, the LEFT button will toggle you  
through the four different sources in the following order:  
9
RGB/Component  
Component  
S-Video  
Composite  
OFF  
ON  
E. DOWN BUTTON  
When no menus are present on-screen, the DOWN button will toggle you  
through aspect ratios in the following order:  
RUNCO  
Anamorphic  
Standard (4:3)  
Letterbox  
When the menu is on-screen, the DOWN button will move the cursor  
down within the menu. When an adjustment item has been selected (i.e.  
brightness), the DOWN button will decrease the value of that function.  
F. RIGHT BUTTON  
When no menus are present on-screen, the RIGHT button will toggle you  
through the four different sources in the following order:  
Composite  
S-Video  
Component  
RGB/Component  
J. DIRECT ACCESS BUTTONS  
These buttons will allow you to directly  
G. MENU BUTTON  
access an aspect ratio, source, or turn the  
unit on or off without having to go through  
any menus. These buttons are:  
Pressing the MENU button will bring up the main menu. If no action is  
taken within approximately 10 seconds, the menu will time-out (disappear).  
Also, if you are in an adjustment mode or function, pressing MENU will  
bring the menu back one level.  
1: Selects COMPOSITE video  
2: Selects S-VIDEO  
3: Selects COMPONENT video  
4: Not used  
5: Selects RGB/COMPONENT  
6: Enables or disables the Installation  
Menu (see page 21)  
H. ENTER BUTTON  
When an item is highlighted on a menu, pressing ENTER will select that  
item.  
I. PROGRAM BUTTON  
If the remote control loses its 'memory' as a result of weak or dead batter-  
ies, it must be re-programmed for the PFP Controller's code set.  
To reprogram the remote, press the PROGRAM button followed by 0,1,3.  
Note: Pressing Enter after typing in the code is not necessary.  
7: Selects the ANAMORPHIC aspect ratio  
8: Selects the STANDARD (4:3) aspect ratio  
9: Selects the LETTERBOX aspect ratio  
0: Turns the PFP Controller ON.  
OFF: Also known as the button left of '0',  
this turns the PFP Controller OFF.  
13  
 
Quick Set-up Guide  
Connection Examples  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
RUNCO INTERNATIONAL  
HAYWARD, CA  
!
MADE IN USA  
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR  
COMLINK OUT  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER. NO USER-  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE CENTER.  
12V FUSE  
AC 120V 60Hz, 15W  
WARNING: TO REDUCE THE RISK OF FIRE  
OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE.  
RGB OUTPUT  
VIDEO INPUTS  
RS-232 IN  
V
H
B
G
R
RGB/COMPONENT  
Y
Pr  
Pb  
S-VIDEO COMPOSITE  
MASK  
SCREEN  
MADE IN USA  
12V TRIGGER  
VCR, Laser  
disc player,  
camcorders  
DTV decoder,  
Progressive DVD  
or Computer  
DVD Player  
Automation  
System  
To DR-300c  
Sattelite  
receiver or  
SVHS player  
While there are many different ways to connect your source equipment to your PFP  
Controller, the examples shown above are the most common and are recommended by  
Runco.  
• COMPOSITE VIDEO INPUT:  
Composite video is the most common type of signal used, but is also the lowest in picture  
quality. Many sources have outputs that are limited to Composite video, such as some VCR’s  
and camcorders. Others, such as laser disc players, actually produce slightly better results  
when using Composite video. While the PFP Controller has an excellent decoder for  
Composite video, it is recommended that Composite video be used only if necessary.  
• S-VIDEO INPUT  
S-Video is the second-best type of signal that can be used, but is MUCH better than  
Composite video. Using such sources as satellite receivers, high-quality VCRs and DVD play-  
ers (with no Component output) will produce a MUCH cleaner and sharper signal. Decoder  
artifacts that are associated with Composite video (dot crawl and ‘rainbows’) are non-existent  
when using S-Video.  
• COMPONENT INPUT  
Component video is the best type of signal that can be used. The most common sources that  
use Component outputs are DVD players, and it is highly recommended that Component be  
used when possible. Component video goes one step beyond S-Video in picture quality;  
chroma (color) information is more resolved and the overall picture appears more well-  
defined.  
• RGB/COMPONENT INPUT  
This port is where all high-resolution signals (such as computers, DTV decoders and progres-  
sive DVD players) must be input. The signal type can be either RGBHV or Component and is  
not processed by the PFP Controller.  
14  
 
Overall Functional Description  
The DR-300c system consists of the PFP Controller and the DR-300c Projector. This sys-  
tem is unique in the way it is controlled; the control center for this system is located within the  
PFP Controller. The PFP Controller tells the Projector to turn on or off, controls its brightness,  
contrast, color temperature and more. All of this is accomplished by Runco's unique ComLink,  
which is the transfer of information between the PFP Controller and the Projector via their  
ComLink ports on a CAT5 cable with RJ-11 ends. Therefore, only the PFP Controller's remote  
control is necessary to control all aspects of this system.  
Besides being the system's control center, the PFP Controller is also a high-quality scaler,  
which outputs all signals in the native resolution of the DR-300c Projector. The Composite, S-  
video and Component (non-progressive) signals are sent through the PFP Controller's 10-bit  
decoder, de-interlaced, then scaled to the native resolution of the Projector. In the case of  
HDTV or progressive DVD signals, these are input to the RGB/Component port.  
In the next chapter, the menu system will be described in detail. There are many adjustments  
available to perfect the DR-300c's image, including typical 'front-panel controls' as well as  
color temperature and other image-quality controls.  
15  
 
Menu Description and Navigation  
Menu Tree  
Tint  
Input Select:  
Color  
Composite  
Brightness  
Contrast  
S-Video  
Sharpness  
>Component  
Luma Enhance*  
Chroma Enhance*  
Color Temperature*  
Color Balance*  
High Definition:  
RGB/Component  
Aspect Ratio Select  
Installer Adjust  
Anamorphic  
Standard 4:3  
Letterbox  
4:3 Screen  
16:9 Screen  
Anamorphic Lens  
16:9 Position  
Keystone  
Picture Orientation  
Lamp Hours  
20  
The menu tree above is an overall glance at the menu system in the DR-300c. This menu is  
shown with the installation mode enabled.  
* These menu items will only appear if the installation mode is enabled (pg. 21).  
Main Menu  
The main menu includes three main sections: Source Selection (Composite, S-Video,  
Component and RGB/Component), Aspect Ratio and Installation. Highlight an item on  
the screen using the green selection cursor and press ENTER on the remote or front panel to  
select and make adjustments.  
16  
 
Source Selection is done by highlighting the desired source with the up or down arrows  
and pressing ENTER. Sources may also be selected by pressing the left or right arrows on  
the front panel or remote, or by one of the direct access buttons on the remote (pg. 13).  
Picture adjustments such as color, tint, brightness, etc, are unique per source.  
Aspect Ratio selection is done by highlighting 'Aspect Ratio' on the main menu and press-  
ing enter. The Aspect Ratio menu will then appear; and either ANAMORPHIC, LETTERBOX  
or 4:3 may be selected. Aspect ratios may also be selected by pressing either the up or down  
arrow buttons, or by one of the direct access buttons on the remote. Blanking and shift  
adjustments are unique per aspect ratio.  
Installation is used for adjustments usually made during the initial installation. This  
includes Screen Type, Keystone and Picture Orientation. ‘Screen Type’ tells the PFP  
Controller what aspect ratio screen the system will be used on (either a standard 4:3 screen  
or a 16:9 screen or 16:9 screen with an anamorphic lens installed) and to output the three  
aspect ratios accordingly. ‘16:9 position’ sets the position of the image on the DMD to top,  
center, or bottom for installation flexibility (pg. 22). This is only applicable if ‘16:9 screen’ is  
selected. Also, the age of the lamp in the Projector (lamp hours) may be checked in the  
Installation Menu.  
17  
 
Picture Quality Adjustments  
Main Menu  
sub-menu  
TINT  
COLOR  
BRIGHTNESS  
CONTRAST  
> COMPOSITE  
S-VIDEO  
COMPONENT  
RGB/COMPONENT  
SHARPNESS  
LUMA ENHANCE*  
CHROMA ENHANCE*  
COLOR TEMPERATURE*  
COLOR BALANCE*  
ASPECT RATIO SELECT  
INSTALLER ADJUST  
* Active only when the installation mode is  
enabled (pg. 21).  
Picture quality adjustments (also known as "Front Panel Controls") are the controls that change differ-  
ent parameters of the image such as the amount of color, black level, etc. While these adjustments  
can be set to suit the needs of the user, there is a way to set these properly. This section will describe  
what each function does and how to adjust them properly.  
To access the Picture Quality Adjustments, press MENU, highlight the active source (indicated by the  
arrow) and press ENTER. The picture quality sub-menu will then appear (see above).  
To make an adjustment to a particular function, highlight the function with the up or down arrow but-  
tons and press ENTER. Once the function is on-screen (i.e. brightness), pressing the UP arrow button  
on the remote or front panel will increase the value of that function; pressing the DOWN arrow on the  
remote or front panel will decrease the value of that function.  
While each of the picture quality adjustments can be set to suit the needs of the user, there is a 'prop-  
er' way to set the adjustments. For setting TINT and COLOR, please refer to the color bar test pattern  
below.  
NOTE: A BLUE FILTER must be used so only the blue color bars can be seen; if no blue color filter is  
available, see if the display device has the ability to mute (turn off) the red and green colors via its  
menu structure (most CRT Projectors have this feature). Blue filters are provided with the Video  
Essentials or AVIA test DVDs.  
Tall color bars  
Short color bars  
Tint  
Color  
18  
 
TINT (also known as 'hue') is essentially the ratio of red to green in the color portion of the  
image. If TINT is decreased, the image will appear redder, and increasing it will cause the  
image to appear greener. To set TINT properly, look at the color bar pattern through a blue fil-  
ter (or mute the red and green outputs). Adjust TINT until the middle two tall color bars match  
the middle short color bars (see color bar drawing).  
COLOR (also known as 'saturation') increases or decreases the amount of color in the  
image. To set COLOR properly, look at the color bar pattern through a blue filter (or mute the  
red and green outputs). Adjust COLOR until the outer two tall color bars match the outer  
short color bars (see color bar drawing).  
For setting CONTRAST and BRIGHTNESS, please refer to the PLUGE pattern below:  
Increase contrast until  
this bar no longer gets  
visibly brighter, then  
decrease contrast slightly  
until a small change in  
intensity occurs.  
Below black  
Above black  
CONTRAST adjusts the white level of the image.Adjust contrast until there is a distinct defini-  
tion between the two brightest bars.  
NOTE: For best results, Runco recommends that CONTRAST be set to '0' or very close to it.  
BRIGHTNESS adjusts the black level of the image. To adjust this properly, adjust BRIGHT-  
NESS until the 'below black' bar JUST disappears, but the 'above black' bar is still barely  
visible.  
NOTE: Some DVD players cannot pass the 'blacker than black' bar (they won't pass  
PLUGE), and that bar will never be visible. In a case like this, adjust the 'above black' bar  
until it is slightly brighter than the background that surrounds it.  
19  
 
SHARPNESS adjusts the amount of high-frequency detail in the image. This can be adjusted  
to the preference of the user. Keep in mind that when SHARPNESS is decreased, fine details  
in the image will become 'soft'; when it is increased, fine details will become sharper but will  
also make the picture appear 'noisy' if adjusted too high.  
LUMA ENHANCE* acts as an edge enhancement, especially around black to white transi-  
tions in the image. Essentially, this has the same characteristics as sharpness but affects the  
edges of objects far more that the rest of the image.  
FREQUENCIES HIGH/LOW affect the overall range of the LUMA ENHANCE feature. For  
example, if using a lower-quality video source such as a VCR, the FREQUENCIES should be  
set to LOW. For a good quality source such as a DVD player, set FREQUENCIES to HIGH.  
To set FREQUENCIES, press ENTER while LUMA ENHANCE is on-screen.  
CHROMA ENHANCE* acts as an edge enhancement, especially around color transitions in  
the image. Essentially, this has the same characteristics as sharpness but affects the edges  
of objects far more that the rest of the image.  
FREQUENCIES HIGH/LOW affect the overall range of the CHROMA ENHANCE feature. For  
example, if using a lower-quality video source such as a VCR, the FREQUENCIES should be  
set to LOW. For a good quality source such as a DVD player, set FREQUENCIES to HIGH.  
To set FREQUENCIES, press ENTER while CHROMA ENHANCE is on-screen.  
COLOR TEMPERATURE* sets the overall color balance of the image. When you select color  
temperature, you’ll have three choices - Temperature1, Temperature2, and Temperature3.  
Temperature 1 raises the black level and changes the flesh tones slightly towards the green;  
better for use in a semi-lighted room. Temperature 2 is the default setting; it produces proper  
flesh tones and black levels for use in a light-controlled environment. Temperature 3 is the  
same as Temperature 1, but with higher black levels for areas of excess ambient light.  
COLOR BALANCE* adjusts the actual grey scale of the image. The ‘Offset’ adjustments  
affect the darker areas of the image, and the ‘Gain’ adjustments affect the brighter areas of  
the image. For example, if there is too much red in the dark areas of the image, decrease  
‘Red Offset’. If there is too little blue in the brightest areas of the image, increase ‘Blue Gain’.  
* Active only when the Installation mode is enabled (pg. 21).  
20  
 
Installation Menu  
Installation Menu  
The Installation menu is where you can adjust the Image Orientation, as  
well as set the type of screen (4:3 or 16:9), shift the image or set blank-  
ing, and even check the age of the lamp in the Projector.  
INSTALLATION  
When the PFP Controller is turned on for the first time, the INSTALLA-  
TION item will not appear in the main menu. To enable the INSTALLA-  
TION menu, there are two options:  
4:3 Screen  
> 16:9 Screen  
Anamorphic Lens  
· With the processor ON and no menus on-screen, simultaneously press  
the ENTER, UP and LEFT buttons (you don't need to hold them down).  
Release the three buttons and press MENU, ensure INSTALLATION is  
now on the bottom of the main menu.  
16:9 Position  
Keystone  
Picture Orientation  
· With the remote control, press button 6 (with no menus on-screen).  
After pressing '6', press MENU and ensure INSTALLATION is now on the  
bottom of the main menu.  
Lamp Hours  
20  
After INSTALLATION has been accessed, press MENU, highlight  
INSTALLATION and press ENTER. This will bring up the INSTALLATION  
MENU, shown to the right:  
Screen Type  
This is where you tell the system what aspect ratio screen you are using, and whether or not you are  
using an anamorphic lens. This MUST be set first before using the system, as the aspect ratios the  
PFP Controller creates will be dependent on this setting.  
There are three options for setting the screen type:  
16:9 screen: If you have a 16:9 aspect screen and are NOT using an anamorphic lens, set 'Define  
screen type' to this. This will allow the system to provide anamorphic and letterbox aspect ratios that  
will fill the screen, and a 4:3 aspect ratio that will occupy the center of the 16:9 screen.  
4:3 screen: If you have a 4:3 screen, set 'Define screen type' to this. This will allow the system to cre-  
ate a full 4:3 image that will fill the screen, and an anamorphic and letterbox aspect ratios will be cen-  
tered vertically on the 4:3 screen.  
16:9 screen with an anamorphic lens: This setting is only applicable if you are using the projector with  
an outboard anamorphic lens. The aspect ratios created by the PFP Controller will appear the same  
as on the "16:9 screen" setting, but will be vertically stretched on the DMD to accommodate the  
anamorphic lens.  
21  
 
16:9 Position  
A coarse shift adjustment that allows a 16:9 image to be displayed on either the CENTER (default),  
TOP or BOTTOM of the device. This is extremely helpful in installations where the Vertical Offset (see  
page 10) cannot be precisely attained. Please refer to the drawings below:  
Active Video Area  
Active Video Area  
Active Video Area  
TOP Position  
CENTER Position (default)  
BOTTOM Position  
The 16:9 POSITION feature can be used in lieu of angling the projector and using keystone.  
It can ONLY be used on 16:9 screens and CANNOT be used if an anamorphic lens is installed on the  
projector.  
NOTE: High definition or computer sources input to the RGB/Component port may require additional  
positioning adjustments. If so, please refer to the Quick Menu on page 24.  
Keystone  
KEYSTONE: Corrects the trapezoidal distortion that results from projecting at an angle:  
A correctly adjusted image  
An image with Keystone error  
This may occur in installations where the projector needed to be angled as a result of a larger vertical  
offset. This keystone feature will correct for trapezoidal distortion for as much as a 15° projector  
angle.  
22  
 
Picture Orientation  
This will set the orientation of the image for your installation. If the Projector will be mounted  
on a table, set this for Floor. If mounting it on the ceiling, select Ceiling. For two-mirror or  
‘straight-shot’ rear-screen applications, select floor rear or ceiling rear as appropriate.  
Lamp Hours  
Lamp Hours displays the number of hours the lamp has been on. With the DR-300c, the lamp  
life is around 1000 hours. This should be checked periodically to keep track of the lamp's  
age, and when the lamp is around 1000 hours old, a new one should be installed to prevent  
lamp failure, including implosion.  
System Reset  
In the event that your PFP Controller appears to have a software problem, or adjustments  
have been made so far out of range that the image is no longer on-screen or discernable,  
you can reset it back to factory values. This sets ALL settings back to factory values, so any  
adjustments made previously will be lost.  
To reset your DR-300c PFP Controller, follow this procedure:  
· Turn off the MAIN POWER switch on the back of the processor  
·
Hold down the DOWN ARROW button, and turn the MAIN POWER SWITCH back  
on. Continue holding the down arrow button until the LED on the front panel blinks,  
then release the down arrow button.  
Once this is done, your processor has been completely reset to factory values. After resetting  
the unit, Composite video will be the active source.  
SYSTEM RESET is not on any of the menus; it must be performed using the instructions  
above.  
23  
 
Quick Menu  
The 'Quick Menu' allows you to position and blank any signal sent through the RGB/Component input.  
This can be done without having to go through the standard menu, as the Quick Menu is done com-  
pletely from the front panel.  
The Quick Menu is only available when you are in the RGB/Component source, and the instal-  
lation mode is active (pg. 21).  
To use the quick menu, press ENTER on the front panel, and observe the front panel display. The fol-  
lowing will be displayed:  
Quick Menu: Shifting  
Press arrows or enter...  
The first mode of the Quick Menu is SHIFTING. When this is displayed, press the up, down, left or  
right arrows to shift the image. For all of the adjustments, the quick menu will time-out 10 seconds  
from the last button press, so ensure that you make the adjustments within that time.  
If you do not need to make any position adjustments or you have completed making them, press  
ENTER again to display the next mode of the shift menu, which is for TOP BLANKING:  
Quick Menu: Top Blanking  
Press arrows or enter...  
To adjust top blanking, press the up or down arrow buttons. Once the adjustments have been com-  
pleted, or no adjustment was needed, press ENTER. The final mode of the quick menu will be dis-  
played, which is for BOTTOM BLANKING:  
Quick Menu: Bottom Blanking  
Press arrows or enter...  
To adjust bottom blanking, press the up or down arrow buttons. Once the adjustments have been  
completed, or no adjustment was needed, press ENTER. You will then exit the quick menu. If you  
need to re-adjust or touch up any of the three adjustments, press ENTER again to re-enter the quick  
menu.  
24  
 
Basic Troubleshooting Tips  
The following is a basic troubleshooting guide that can assist you in resolving typical prob-  
lems may result in normal operation. If you have encountered problems that are not listed in  
this guide, please contact your Runco dealer for assistance.  
PROBLEM  
POSSIBLE CAUSE  
SOLUTION  
The projector does not turn on  
after initial installation. The  
Power LED on the front of the  
PFP Controller stays yellow  
after the power button is  
pressed.  
· The RJ-11 (ComLink) cable is  
not connected between the PFP phone-type cord. Ensure it is  
Controller and Projector, or is  
made improperly.  
· The projector is not plugged in, · Ensure there is good conti-  
or its AC outlet is not active. nuity in the RJ-11 cable.  
· Use a standard RJ-11  
firmly plugged into both the  
Controller and the Projector.  
Look at its power LED inside the · Verify that the AC outlet is  
input panel and see if it is illumi- active, or that the Projector is  
nated.  
plugged in.  
The projector and PFP  
Controller are both on, but  
there is no video image on-  
screen.  
· The PFP Controller is on the  
wrong source.  
· The PFP Controller is on the  
correct source, but the source  
itself is off.  
· Press MENU on the  
Projector's remote, and look  
to see which source is active  
(the arrow will be pointing to  
the active source). Select the  
correct source as appropriate.  
· Turn on the source. It is rec-  
ommended that all sources be  
turned on first BEFORE the  
DR-300c.  
The projector is producing a  
'split screen' or an otherwise  
scrambled image.  
· A progressive scan DVD is  
plugged into Component input  
rather than the RGB/Component Progressive scan must go into  
· Only NTSC/PAL can be input  
to the Component input.  
input.  
RGB/Component.  
The image appears too bright,  
and there is a loss of definition · The DVD player is set for a  
in the brightest areas of the  
image.  
· Contrast is set too high.  
· Turn down the CONTRAST  
level on the PFP Controller.  
Mid-range is 0; it is recom-  
mended to keep it below 20 to  
prevent this problem.  
· Set the DVD player for a  
nominal output (no boost or  
gain).  
high-level output.  
· The video signal has not been  
terminated properly somewhere  
in the system.  
· Ensure all video signals are  
terminated in 75 Ohms.  
25  
 
The image appears too  
'washed out', or the darkest  
areas of the image appear too for too high of a brightness  
bright.  
· Brightness is set too high.  
· The DVD player may be set  
· Turn down the BRIGHTNESS  
level on the Controller. If possi-  
ble, use a PLUGE pattern to set  
the brightness level properly.  
· Set the DVD player for a nomi-  
nal output (no boost or gain).  
level.  
The colors of the image  
appear abnormal  
· The Red, Green and/or Blue  
outputs of the PFP Controller or on the back of the PFP  
· Check the cable connections  
inputs to the Projector are  
reversed.  
Controller or on the Projector.  
· The Pr and Pb inputs on the  
Component input on the PFP  
Controller are reversed  
The image appears keystoned · The Projector has been  
· Adjust Keystone, see page 22.  
(trapezoidal).  
mounted too high or too low in  
respect to its vertical  
offset.  
The Projector will not turn on, · The PFP Controller may have  
· Unplug the Controller for 2  
minutes; plug it back in a re-try.  
· Perform a system reset on the  
Controller (see page 23), and  
then re-try.  
and the power LED on the  
front of the PFP Controller is  
blinking red.  
'locked-up'.  
The Projector will not turn  
back on after it was powered- for two minutes after power-  
down, or the image disap-  
pears during operation.  
· The Projector will not turn on  
· Wait two minutes until the LED  
on the front of the PFP  
Controller turns red.  
· Check the error light in the  
Projector.  
down to protect its bulb.  
· The bulb has failed  
The Projector tries to turn on  
but the lamp does not come  
on and the status LED on the  
Projector is blinking.  
If this happens, the projector may have detected a fault. The red  
Status LED will blink in several different ways, describing different  
faults:  
On constantly: The bulb has exceeded 1000 hours.  
Blinking on and off every second: The lamp cover is not on  
properly. Contact your Runco dealer.  
Blinking on and off every 4 seconds: The Projector has over-  
heated. Ensure nothing is blocking the Projector's ventilation  
holes.  
Blinking on and off every 8 seconds: The fan has stopped.  
Contact your Runco dealer.  
Blinking on and off every 12 seconds: The lamp did not turn on.  
If the Projector was turned on and off too quickly, this may hap-  
pen. Allow the Projector to settle for 5 minutes, and try again. If  
the same fault is reported, contact your Runco dealer.  
26  
 
RS-232 Communications  
General Information  
Baud rate: 9600 (fixed)  
Bits: 8  
No Parity  
All protocol in ASCII format  
RS-232 input connector pin numbers: TxD= Pin# 2, RxD= Pin# 3, GnD= Pin# 5  
Command format (single command): command value (i.e. brightness 30).  
NOTE: A space (not an underscore) or comma may be used between the command and its value.  
Command string format: command,command value, command etc.  
(i.e. COMPOSITE,BRIGHTNESS 30,ANAMORPHIC)  
NOTE: In between commands, a comma must be used; a comma or space may be used in between  
a command and its value.  
Other notes:  
· For command strings, a maximum of 255 characters can be used in a single string.  
· If it is necessary to input multiple commands, they should all be together in a single string. Inputting  
commands one at a time requires a 15 second delay between commands, as the information is  
stored into non-volatile memory after each command.  
· For values not automatically stored (see next paragraph), the command "!STORE" must be sent  
in order for the PFP Controller to keep the settings. Otherwise, the values will be considered  
temporary and will revert to their stored settings upon source change or power-up.  
· The "Value stored" column refers to a command that is either automatically stored or if it must be  
manually stored with the "!STORE" command.  
· PARAMETER min/max refers to a function's minimum and maximum value range. Inputting  
values above or below their range may cause unpredictable (but not fatal) results.  
· When connecting RS-232 to the "----------", you may have to add a delay in between characters.  
For example in an AMX system you would add the following line :  
(***********************************************************)  
(*  
STARTUP CODE GOES BELOW  
*)  
(***********************************************************)  
DEFINE_START  
SEND_COMMAND PFP,'SET BAUD 9600,N,8,1'  
SEND_COMMAND PFP,'HSOFF'  
SEND_COMMAND PFP,"'CHARD-200'" (* SETS DELAY IN MICROSECONDS BETWEEN CHARACTERS *)  
This will increase the reliability in receiving the code. For other systems you may have to contact the  
manufacturer to find out how to set the delay.  
27  
 
RS-232 Commands  
COMMAND  
PARAMETER (min/max)  
Value stored?  
DESCRIPTION  
ON  
OFF  
COMPOSITE  
NA  
NA  
NA  
NA  
NA  
YES  
Turns PFP Controller on  
Turns PFP Controller off  
Selects the Composite  
Video input  
SVIDEO  
COMPONENT  
HD  
NA  
NA  
NA  
YES  
YES  
YES  
Selects the S-Video Input  
Selects the Component input  
Selects the RGB/Component  
input  
ANAMORPHIC  
STANDARD  
NA  
NA  
YES  
YES  
Selects the anamorphic  
aspect ratio  
Selects the standard (4:3)  
aspect ratio  
LETTERBOX  
TINT  
COLOR  
NA  
YES  
NO  
NO  
NO  
Selects the letterbox aspect ratio  
Sets a value for tint  
Sets a value for color  
-127/127  
-127/127  
0/1  
AGCCOLOR  
0=Disable Color AGC  
1=Enable Color AGC  
BRIGHTNESS  
CONTRAST  
AGCCONTRAST  
0/100  
0/100  
0/1  
NO  
NO  
NO  
Sets a value for brightness  
Sets a value for contrast  
0=Disable Contrast AGC  
1=Enable Contrast AGC  
Sets a value for sharpness  
Sets a value for high-frequency  
chroma edge enhancement  
Sets a value for low-frequency  
chroma edge enhancement  
Sets a value for high-frequency  
luminance edge enhancement  
Sets a value for low-frequency  
luminance edge enhancement  
Selects the Projector’s color  
temperature  
SHARPNESS  
CHROMAHIGH  
0/255  
0/127  
NO  
NO  
CHROMALOW  
LUMAHIGH  
0/127  
0/127  
0/127  
1/4  
NO  
NO  
NO  
NO  
LUMALOW  
TEMPERATURE  
28  
 
COMMAND  
PARAMETER (min/max)  
Value stored?  
DESCRIPTION  
!STORE  
NA  
YES  
Stores the current set of values  
(all values) into non-volatile  
memory  
!RESTORE  
!FACTORY  
NA  
NA  
YES  
YES  
Restores the stored values  
Restores all values to factory  
default levels  
!STATUS  
NA  
NA  
Asks the Controller to provide  
the hardware information,  
current values and system status  
to the automation system  
Restarts the PFP Controller  
(same as turning it on and off)  
Enables the Controller to echo  
back commands and values to  
the automation system  
!RESTART  
!ECHO  
NA  
NA  
NO  
NO  
!NOECHO  
NA  
NA  
NA  
NO  
NA  
NA  
Disables the PFP Controller's  
character echoing  
!INSTALLMODEOFF  
!INSTALLMODEON  
Disables the Installation menu  
(removes it from the main menu)  
Enables the Installation menu  
(enables it on the main menu)  
Enables the service mode  
Disable the service mode  
Adjust the Red Gain of image  
Adjust the Green Gain of image  
Adjust the Blue Gain of image  
Adjust the amount of Red in the  
dark areas of the image  
!SERVICEMODEON  
!SERVICEMODEOFF  
RGAIN  
GGAIN  
BGAIN  
NA  
NA  
-64/64  
-64/64  
-64/64  
-64/64  
NA  
NA  
NO  
NO  
NO  
NO  
ROFFSET  
GOFFSET  
BOFFSET  
-64/64  
-64/64  
NO  
NO  
Adjust the amount of Green in  
the dark areas of the image  
Adjust the amount of Blue in  
the dark areas of the image  
29  
 
DR-300c Projector Dimensions  
Top View  
Status  
Power  
16.186  
Front View  
3.398  
4.028  
Side View  
13.211  
30  
 
PFP Controller Dimensions  
Front Panel  
17.45"  
ratio  
<
>
3.5"  
ratio  
T
M
P
I
X
E
L
F
O
R
P
I
X
E
L
Rear Panel  
17"  
CAUTION  
RUNCO INTERNATIONAL  
HAYWARD, CA  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
!
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR  
MADE IN USA  
COMLINK OUT  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER. NO USER-  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE CENTER.  
12V FUSE  
AC 120V 60Hz, 15W  
3.025"  
WARNING: TO REDUCE THE RISK OF FIRE  
OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE.  
RGB VIDEO OUTPUT  
VIDEO INPUTS  
RS-232 IN  
V
H
B
G
R
RGB/COMPONENT  
Y
Pr  
Pb  
S-VIDEO COMPOSITE  
MASK  
SCREEN  
MADE IN USA  
12V TRIGGER  
Top Panel  
17"  
16"  
17.45"  
Side Panel  
3.5"  
16"  
31  
 
Specifications  
DR-300c Projector:  
Projector Type:  
Digital Light Processing™ (DLP)™  
Native Resolution: Native 1024 x 768, Widescreen 1024 X 576  
Video Standards:  
Lamp:  
NTSC, (PAL/NTSC International version)  
135 W NSH lamp  
Lamp Life:  
1000 hours  
Light Output:  
Picture Size:  
Throw Distance:  
1000 ANSI lumens  
36 to 200 inches diagonal  
Minimum= 2.0 x screen width  
Maximum= 2.3 x screen width  
Vertical offset:  
16:9 screens: .265 x screen width / 4:3 screens: .173 x screen width  
The vertical offset numbers are within ± 5% tolerance due to minor variance  
between units. The offset is calculated from the center of the lens.  
Inputs:  
Composite, S-Video, RGB/Component  
Aspect Ratio:  
3 Memories:  
4 x 3 Screens: 4:3 aspect fills the screen, anamorphic and letterbox  
aspects occupy center of 16:9 portion of screen (black bars  
above/below image)  
16 x 9 Screens: 16:9 and anamorphic aspects fills the screen, 4:3  
aspect occupies center of 16:9 screen (black bars on sides of image)  
16 x 9 Screens with Anamorphic Lens (optional): same ratios as 16:9  
screens; but maximizes resolution as all pixels are active on screen  
Contrast Ratio:  
Bandwidth:  
800:1 (ANSI method)  
80 MHz  
Power  
Requirements:  
115VAC 60 Hz, (90-240V auto-switching power supply International version)  
2.2A (115VAC, 60 Hz), 1.1A (220-240V, 50-60 Hz International version)  
Current:  
Dimensions:  
Width: 16.186 in. / 411 mm  
Depth: 13.211 in. / 336 mm  
Height: (w/feet) 4.028 in. / 103 mm  
16 lbs. / 7.26 kg  
Weight:  
Safety Regulations: Complies with FCC Class ‘B’, CE, C-Tick  
Operating  
Environment:  
32-104° F (0-40° C)  
Humidity:  
40-80%, non-condensing  
Warranty:  
Service Labor and Parts (except lamp): Runco warrants the product for two  
(2) years from the date of delivery to the end user.  
Lamp: 6 months or 1000 hours (which ever comes first).  
32  
 
PFP Controller:  
Inputs:  
(1) Component, (1) S-Video, (1) Composite, (1) RGB/Component (DB-15)  
Input standards:  
NTSC, (PAL/NTSC International version),  
HDTV @ 480p, 540p, 720p and 1080i (via RGB/Component input)  
Aspect Ratios:  
Control Options:  
Bandwidth:  
Anamorphic, letterbox, 4:3  
Infrared, RS-232, Front Panel  
Video inputs: 5.5 MHz  
RGB/Component: 100 MHz  
Operating  
Environments:  
41-95° F (5-35° C) 0-90% humidity (non-condensing)  
Dimensions:  
Width: 17.45 in. / 443.23 mm  
Depth: 16 in. / 406.40 mm  
Height: 3.5 in. / 88.90 mm  
Weight:  
16 lbs. / 7.26 kg  
Power  
Requirements:  
115VAC 60 Hz, (90-240V auto-switching power supply International version)  
Safety Regulations: Complies with FCC Class 'B', CE, C-Tick  
Warranty: Service Labor and Parts: Runco warrants the product for two (2) years from  
the date of delivery to the end user.  
Supplied Accessories  
• Remote Control with 2 AAA batteries  
• Rack Mount hardware  
• The Installer friendly “Slam Dunk” cable, which includes VGA to RGB adaptor and mini DIN-8 to RJ-  
11 adaptor  
• Power cables (one for Projector, one for PFP Controller)  
• 50’ RJ-11 cable  
• User’s Manual  
• Warranty information  
33  
 
 
RUMA-008100 rev 10-01  
Runco International 2463 Tripaldi Way Hayward, CA 94545 ph (510) 293-9154 fax (510) 293-0201 www.runco.com  
 

Radio Shack Karaoke Machine Hi Power CD+G Karaoke System User Guide
Raypak Swimming Pool Heater 992B 1532B User Guide
RCA Camcorder CC6394 User Guide
RocketFish Video Gaming Accessories RF GPS31104 User Guide
Samsung Clothes Dryer DV331AE User Guide
Samsung Flat Panel Television LE20S8 User Guide
Samsung Home Theater System AH68 01701V User Guide
Samsung Projection Television SP 50L7HR User Guide
Samsung Refrigerator 65602 User Guide
Senco Power Screwdriver DS200 AC User Guide